• Elettronica, Sistemi,Avionica. Spazio

07/04/2016 – Present IPC Project Leader ( Alten/Positech Consultant ) Magneti Marelli Electronics (FCA Group) – Corbetta (MI – Italy) Project Leader involved in: – Management, coordination, planning and tracking of activities for firmware system design and code development/test for car cluster (IPCs) of FIAT 500x and JEEP Renegade. – Supervision to LPG functionalities integration. – Risk analysis, time/resources tracking, resources/workload/cost impact analysis. Requirements analysis. – Firmware functional tests. Duties: – Project Management – Project Planning/Tracking – Activity Analysis and timing – Task/Resource assignment – Requirements Analysis – Project Status – Project Documentation – IPC functional debug test (CANBUS) Tools: IBM Rational Doors, IBM Rational Change, Vector Canalyzer, Canbus, MS Project, MS Excel

21/03/2016 – 04/04/2016 Power Electronics Design Engineer ( Alten/Positech Consultant ) Alstom Transportation – Sesto San Giovanni (MI – Italy) Design and prototyping of a Power supply/ AT Sensor/ DC/DC Chopper board for application in Alstom Z1 railroad electronics revamping programme. Used Software: Mentor Graphics CAD

13/04/2015–18/03/2016 UAV System Engineer ( Alten/Positech Consultant ) Piaggio Aerospace SpA, Albenga (SV – Italy) P.1HH Unmanned Aerial System – System Engineer

– UAV LOS Datalink System Engineer – System and equipment requirement engineering – System and equipment Test Specification/procedures – System Documentation – Compliance analysis – System /equipment qualification procedures – E3 Facilities – Flight Test Intsrumentation (FTI) support – Ground/Aircraft systems – Ground activities – Functional/Performance Test in situ for air/ground segment systems – On Site Test (ATP, FAT) Aircraft Segments – Antenna analysis – Link Budget Analysis – Power Budget Analysis – Suppliers interfacing and support Used Software: MS Office Suite, CST Microwave Studio, Matlab Used Hardware: Vector Network Analyzer, Spectrum Analyzer Norms: RTCA-DO 160; RTCA-DO 254; RTCA-DO 178; MIL- STD – 810; STANAG 4671 02/12/2013–10/04/2015 Space Electronics ATE Engineer, Space RF Design Engineer IMT srl – Apulia Aerospace Cluster, Valenzano (BA – Italy) ATE Engineer, Hardware Design Engineer involved in following programs: – Satellite for High Resolution Infrared Application – SHIRA Project – Apulia Aerospace Project Qualification Campaign (ESA/ASI) – ERMES program ( Lazio Satellite program) – Nano Sat Project – Space/ Defence Qualification on behalf of Thales Alenia Space, Selex ES, OHB, RGM and more ▪Components and systems design and prototyping: RF, Analog, Mixed Signal component/system development: Design, Simulation and prototyping in spaceborne, payload, tlc, satellite domains. used software: Agilent Genesys, Agilent ADS , CST Microwave Studio, Altium Designer. ▪Components/systems testing – E3 Facility: component/system testing: test specification, measure benchmark set up, instrumentation set up, lab/test automation. – Electrical characterization and test – UHF / RF / EHF measurements and testing – Duration Test (Life test, relife test) – Infant Mortatlity Test (Burn in test, Stress test) – Environmental Test (Humidity/Pressure Test, Temperature Test, Thermal Schock Test.) – Drift Test – Measure statistics – Data Processing

used software: NI Labview, NI MaX, Agilent Vee, Microsoft Excel used hardware: Performance Network Analyzer, Vectorial Network Analyzer, Spectrum Analyzer, Oscilloscopes, Signal Generator, Power Meter, Frequency Counter,Temperature Chamber, Welding Torch, optical Microscope, ultra sound bath, LCR Meter, NI cDAQ, NI PXI Platform. ▪ Test Board Development Test Board specification, design, simulation and prototyping used software: Altium Designer, Agilent ADS used hardware: Oscilloscopes, Signal Generator, Power Meter, Frequency Counter, Welding Torch, optical Microscope, ultra sound bath. ▪ Real Time Process Control software coding, hardware and controls (probes/sensors) set up, data logging and processing. used software:NI Labview, NI MaX, Microsoft Excel. used hardware: NI cRio, NI cDaq ▪ Reference Norms: ▪ MIL-STD-810, MIL – STD – 202G, MIL – STD – 750F ▪ MIL-PRF- 31032B, MIL – PRF – 19500P, MIL STD 883 ▪ ESCC 12100 ▪ ESCC 2023102 ▪ ESCC 3001/3006/3011 ▪ ESCC 4001/4006 ▪ ESCC 9202/080 ▪ Customer Specifications (Thales Alenia Space, Selex ES, Sitael SpA,GelCo SpA, RGM, etc) 08/06/2012–30/09/2013 Research Engineer – Micro and Nanotechnologies for Applications in EHF Band for Space and Defence Domains University of Messina – Matter Physics Dept., Messina (Italy) Research Engineer in micro and nano technologies for application in EHF band – European Project "PANREX". Researcher and project engineer in defence electronics / aerospace nanotechnologies, RF electronics, MEMS (Micro Electro Mechanical Systems), TLC, spintronics,project management. accomplished tasks: ▪ Measurement and characterization in frequency domain (S parameters) for miniaturized devices by Virtual Network Analyzer (VNA), DC measures, oscilloscope measurement. used softwares: MSWord, MSExcel, Mathworks Matlab, CST Microwave Developer. used instrumentation: Virtual Network Analyzer, Maury Microwave test fixtureMT964B1-10 – 7mm, Oscilloscope. ▪ Project and design of Yagi Uda antennas with working frequency 8 GHz used softwares:MSWord, MSExcel, Mathworks Matlab,Nec2. ▪ Led/Laser diodes characterization. used softwares: MSWord. used instrumentation: signal generator, power meter, spectrometer, lenses, photo diodes. ▪ RF resonators design. used softwares: CST Microwave Developer.

▪ RF systems design and simulations. used softwares: ADS Agilent. ▪ Statistics simulations for failure rate measurement. used softwares:MiniTab. ▪ Management case studies. used softwares: MSProject. 01/04/2013–30/06/2013 RF System / Project engineer Selex ES SpA, Palermo (Italy) Project Engineer for Radar subsystems: ▪ Design of a miniaturized X band pass band filter. used softwares:MSWord, Agilent Genesys,MSExcel. ▪ Design, simulation and system analysis for an up converter module to embed in AESA Radar for JSF Programme. used softwares:MSWord, Agilent Genesys,MSExcel. ▪ RF mixers characterization. used softwares:MSExcel. used instrumentation: Agilent signal generator, spectrum analyzer. ▪ Design, MTBF analysis for Radar subsystems electronic components.used softwares:PTC Windchill. 10/12/2009–08/06/2012 Project Manager, Project Engineer Esapower srl, Vibo Valentia (Italy) Project management and engineering for design and realization of big size photovoltaic power plants. Commission manager and resources coordination. ▪ Commission management and coordination. used softwares:Gantt, MSExcel. ▪ Project teams coordination and management. used softwares:Gantt, MSExcel. ▪ Suppliers management and relationship with public and private organization for permitting procedures. ▪ Solar, electrical and graphic development of project. used softwares:PVSyst, Autocad, Carnaval,MSWord, MSExcel,MSPowerPoint. ▪ Works management (100/150 workers/day in building sites) . 11/06/2012–30/09/2013 Second Level Master University Course – Micro and Nanotechnologies EHF Band Applications EQF level 8 University of Messina – Matter Physics Dept., Messina (Italy) Master Course in Micro and Nanotechnologies for EHF Band Application – University of Messina, Selex ES Spa, ISMN-CNR, Messina (Italia) Industrial Researcher on behalf of European Joint Strike Fighter Programme

Project Engineering Defence/Space electronics RF Electronics, MEMS, Telecommunications, Spintronics, Optoelectronics, Project Managemetn Main Developed Activties and Tasks: ▪ Measurement and Frequency characterization of miniaturized devices ▪ RF components design for defence and space applications ▪ Antenna system design and test/measurements ▪ Laser leds diode Optical CharacterizationCaratterizzazione 20/03/2011–11/12/2011 Chartered Engineer – Information/Electronics Domains Sector A – Senior EQF level 7 University of Calabria – Engineering Dept., Rende (Italy) 20/10/2001–05/05/2009 Master Degree in Electronics/Electrical Engineering EQF level 7 University of Calabria – UNICAL, Rende (Italy) Main Subjects: Electronics Matter Physics Computing Coding Electronic Measurement Digital/Analog/Mixed Signal/Power/RF El Processes and Technologies Microsystems

31/03/2006–10/06/2006 English Trinity College Certificate – Level B2 EQF level 5 English Trinity School, Rende (Italy) English Skills and Attitudes writing, reading and speaking skills 15/09/1995–15/07/2000 Classic and Human Studies Diploma EQF level 4 Classic Lyceum "Bruno Vinci", Nicotera (Italy) Italian language and literature Latin language and literature Ancient Greek language and literature English language and literature History Philosophy Maths Physics Informatics

Chemistry Biology Mother tongue(s) Italian

Inglese B2 C2

Job-related skills Project and Design for Analogic, Digital, Mixed Signal, RF Electronic System Engineering in Avionics and Space Domains AIT/ATE/E3 Test Engineering Project Management Project Planning Digital competence Operating Systems: Windows Tools: Electronic Design Automation: ORCad Capture, ORCad Pspice, ORCad CIS, Altium Designer, Mentor Graphics, AWR Microwave Office, Agilent ADS, Agilent Genesys, Xilinx ISE, AVR Studio, NEC2, Ansys HFSS, Ansoft Designer, Eagle Test and Automation: NI Labview, NI MAX, Agilent Vee, GPIB Protocol, VISA Protocol. CANBus Mechanical Design: Autocad 2D Analysis and Model Design: Mathworks Matlab, Matlab Simulink, MiniTab, PTC Windchill Solar Design: PVSyst, Carnaval Management: Gantt, MS Project, MS Excel Languages: Java, C, C++,Assembly, VHDL, Verilog, Matlab, HP-IB, G-Code IDE: Eclipse Driving licence B